- Open Access
Median knock-down time as a new method for evaluating insecticide-treated textiles for mosquito control
© Skovmand et al; licensee BioMed Central Ltd. 2008
Received: 01 November 2007
Accepted: 27 June 2008
Published: 27 June 2008
Insecticide treated bed nets are major tools for the Roll Back Malaria campaign. There are two types of Long-Lasting Insecticide-treated Nets (LNs) on the market: coated nets and insecticide-incorporated nets. Nets provided to this market need a recommendation from the World Health Organization to be purchased by donors and NGOs. During laboratory study (phase I), the first step consists in evaluating the wash resistance of a new LN product. When insecticide-incorporated nets are washed, it takes time to regenerate the insecticidal activity, i.e. insecticide must migrate to the net surface to be accessible to mosquitoes. The interval of time required for regeneration must be carefully determined to ensure the accuracy of further results. WHOPES procedures currently recommend the determination of the regeneration time by using mortality data. However, as mortality cannot exceed 100%, a LN that regenerates a surface concentration exceeding the dosage for 100% mortality, will have its regeneration time underestimated.
The Median Knock Down Time (MKDT) was determined as function of insecticide dosage on an inert surface, glass, and on polyester nettings using an acetone solution or a simple emulsion. Dosage response was also established for mortality data. The same method was then applied to a commercially polyethylene netting, currently under WHOPES evaluation, to determine the dynamics of regeneration as function of repeated washings. The deltamethrin content of these nets was estimated by Capillary Gas Chromatography (GC-ECD).
MKDT was a linear function of log insecticide dosage on glass as on nettings. Mortality data were either 0 or 100% for most concentrations except for a narrow range. MKDT was log linear function of total deltamethrin content in a commercial polyethylene net exposed to washings. The regeneration time of this net increased with the number of washes and MKDT became higher. A new, easy and rapid method to determine MKDT is suggested.
The MKDT is linearly correlated to log dosage on a given substrate and shows no saturation as mortality data do. It is suited to determine regeneration time of a product that is exposed to a stress, like washing or heating, where the process impacts on the bio-availability of the insecticide. Mortality data are useful for measuring product efficacy, whereas MKDT are better to measure dynamics of surface concentration like regeneration after a stressing process. Change in MKDT can be used to illustrate the loss of insecticide due to washing, but the slope of the curve is product and surface-dependent.
Long-Lasting Insecticide-treated Nets (LNs) and tarpaulins have been developed for controlling malaria vectors. Among these are products where the insecticide is slowly released from a matrix of a polymer like polyethylene or polypropylene. This technology is basically different from that of the coating technologies. In the latter, all insecticide is present in a coating at the surface of the material, whereas in the first, most of the insecticide is inside the matrix at any time. Upon removal by washing, rubbing or UV destruction, new insecticide must migrate to the surface of the net to regain activity, i.e. regeneration. After abrupt removal of insecticide (due to washing) the regeneration time becomes the parameter that determines how fast the tool again becomes effective for mosquito control.
Nets and other tools that target vector control and especially the currently large, donor financed market must pass a series of tests organized by WHOPES (WHO Pesticide Evaluation Scheme) to have a chance to be sold to these international organizations. The WHO procedures recognize the two types of impregnation and describe a protocol that divides these products into regenerating and non-regenerating products, the latter meaning regeneration in less than a day . The protocol describes that a net is washed thoroughly to remove most or all insecticide from the surface. The net is then exposed to bioassay on succeeding days to determine the regeneration time. The method determines the percentage of Knock-Down after 1 hr (KD60) and the percentage of mortality after 24 hr. The time required (in days) to reach a stable mortality level is the period required for regeneration of the net . Thereafter, nets are washed or bioassayed at intervals of time determined by this regeneration time to follow the insecticide exhaustion process. A net is regarded as exhausted if mortality drops below 80% and/or KD60 below 95%. Since percentages can never be more than 100%, the method cannot follow the regeneration process happening when 100% mortality is reached. The time for the surface concentration to become stable may be much longer. When this potentially too short interval is used to determine the regeneration time and, therefore, wash intervals, the net may fail in the assay after few washes since not enough time is given for regeneration before the bioassay. On the contrary, it may resist more washes since the amount removed per wash is too low and the regeneration process is interrupted by the next wash.
The median knock-down time (MKDT) does not have the disadvantage of reaching a maximum level. It is expected to be directly correlated to the insecticide concentration on the surface, at least for fast acting insecticides such as pyrethroids . The MKDT method was first developed by Curtis et al  to obtain a bioassay with a fast data generating because of problems with holding mosquitoes. It was later described in two WHO meeting reports from 1996 and 1998 [4, 2] as a better method for measuring loss of insecticide from dipped bed nets, but the method is not included in the current WHOPES procedures for bed net evaluations .
The purpose of this study is to examine whether MKDT is dependent on insecticide dosage on various treated materials, and if this method can be used to determine with more accuracy the regeneration time of LNs. As part of this study, a new test method is proposed where the contact to the treated material is forced, and where the mosquitoes rest only on the treated surface and are relatively easy to observe. The increase in MKDT with the amount of insecticide washed out was followed by chemical analysis. This method compared the initial concentration of insecticide in the net with that left after one to 20 washes.
Regeneration time is defined by WHO  as the time passing for the insecticide to stabilize at the surface after removal of the initial surface cover of insecticide in three consecutive washes as measured with mortality data. In this article, the regenerating time was determined by measuring the time for the median knock-down time (MKDT) to become stable. Further, the MKDT was determined before net washing and daily after net washing for each round of five washes until 20 washes (the WHO threshold for LN).
Anopheles gambiae s.s. Kisumu strain was used. This strain is fully susceptible to insecticides and has been kept at the LIN (Laboratoire de Lutte contre les Insectes Nuisibles, IRD, Montpellier, France) laboratory since 1992. Two- to five-day old, non blood fed females were used for the bioassays.
Insecticide and net materials
Technical deltamethrin from Tagros, India, was used for the impregnations. Serial dilutions of deltamethrin dissolved in acetone were dripped on glass plates or on polyester nets that had been washed once to remove dust and yarn oil. Deltamethrin emulsion was made by dissolving the technical powder in xylene and emulsifying with an oil emulsifier, Polyoxyethylene 10 cetyl ether (Brij 56, Uniqema, Belgium), and hot water. This simple formulation is stable after rapid cooling and used for impregnation of net swatches by dripping the solution on the net.
The polyethylene nets NetProtect (with deltamethrin locked in the matrix) used for the wash resistance study were provided by Intelligent Insect Control, France.
The washing procedure followed the protocol described in WHO . In short, 25 × 25 cm net samples are put into 1 L bottles containing 500 ml of soap water (2 g/L). The bottles are introduced in a water bath at 30°C regulated with a thermostat and shaken for 10 min, then transferred to bottles with clean water for rinsing in the same set-up.
The deltamethrin content was determined on unwashed and washed Netprotect samples using the following analytical method. Deltamethrin was extracted from the samples by heating under reflux for 60 minutes with 40 ml xylene. The extract was let to reach ambient temperature, filtered through a Büchner funnel containing a filter paper and a filter aid and quantitatively transferred into a 50 ml volumetric flask. The flask was filled up to volume with xylene. A 10-time dilution was achieved in xylene. The final extract was finally analyzed for determination of deltamethrin by Capillary Gas Chromatography with 63Ni Electron Capture Detection (GC-ECD) using the external standard calibration.
MKDT as function of log insecticide concentration was determined for laboratory insecticide treated materials and the slope of the effect curves were compared using Statistix for Windows, 8 (Analytical Software, 2003, Tallassee Fl, US).
Mortality of An. gambiae females remained constant at 100% for a wide range of concentrations on glass plates, but dropped sharply within a short interval of concentrations (from 1 to 5 mg/m2) for nets treated with an acetone solution of deltamethrin dripped on net (Figure 2).
Chemical analyses were carried out on samples drawn from the pool of net samples washed and used in bioassays. These analyses were compared to MKDT values after regeneration, meaning when these values were stable. A log linear relation was then found between MKDT and dosage deltamethrin/m2.
New types of bed nets are being made available in the current, worldwide campaign against malaria. Many of these nets are or have been evaluated in the WHOPES in a procedure combining initial laboratory tests followed by semi field tests and evaluation of field tests programmed in co-operation with WHO or accepted as supplementary data.
Whereas the new WHO test protocol  uses 24-hour mortality and KD effect only, this study shows that additional information can be obtained by adding median time measure for knock down, MKDT. This complementary method is useful for measuring bio-availability of insecticide on the surface of a net and regeneration time. It has no saturation point and can measure the time for stable surface concentration, even when mortality has gone into saturation at 100% long before. Accordingly, it is a suitable technique to determine regeneration time. The method was originally suggested as a better method than mortality data for evaluating loss of insecticides from dipped nets because it does not saturate at 100% , but is not part of the current WHOPES protocol for bed net evaluations .
Acetone solutions dripped on glass or polyester net leaves only the deltamethrin on the substrate upon drying. Yet, there is a big difference between the effects of deltamethrin on net to that of deltamethrin on glass plate, the latter being much more effective than the former. It is possible that the acetone let the deltamethrin partly enter into the polyester yarn surface. In both cases, there is a dose-relationship between deltamethrin and MKDT. Interestingly, a simple W/O emulsion of deltamethrin from polyester net gave shorter MKDT values than the solvent solution, probably showing that deltamethrin is easier transferred from the net treated with the emulsion. For all three surfaces/formulations, there is a linear correlation between log concentration of insecticide and MKDT, meaning that MKDT for a given formulation and product can be used to indicate the biologically active surface concentration. A log linear correlation was also found between MKDT measured on a commercial polyethylene net and the dosage of deltamethrin in this net (mg/m2) determined in chemical analysis.
Contrary to that, concentrations of the range 0.25 to 50 mg deltamethrin/m2 gave 96–100% mortality on glass plates. For deltamethrin acetone solution dripped on net, mortality changed from near 0 to near 100 in a narrow range between 1 and 5 mg deltamethrin/m2. Obviously, mortality data can be used for threshold measurements, but will then be very susceptible to small variations in surface concentration or insect susceptibility.
The data also show that for a commercially available polyethylene net incorporated with deltamethrin, regeneration time increased along with exhaustion of the net by washing: the more the net was washed, the longer it took before a stable level of MKDT was reached. Further, the fact that the stable level of MKDT increased with washings indicates that the stabilized surface concentration declined as the yarn was exhausted of insecticide. This indicates that the process involved is a migration of a chemical from a solid material and can be approached with Fick's second law of diffusion: J(t) = D * C, where C is the concentration of insecticide in the matrix, and D is the diffusion constant. The diffusion rate J(t) changes with the concentration in the yarn. The simplified version of Fick's law presented above ignores the surface concentration that is low after wash off, but as this one increases, the diffusion stops. By repeated removal of the surface layer of insecticide by washing the yarn content of insecticide decreases, the migration rate becomes slower and the surface concentration became lower.
This explanation is supported by the chemical analytical data (Figure 6). These show a log linear decline in total deltamethrin as function of the number of washes corresponding to a wash off rate of 1.23% per wash. This is only possible when the regeneration process continued to stabilization where there is a constant ratio between surface concentration and total concentration. The data do not prove if the washing process removes all insecticide on the surface or just a certain percentage. However, the important point is to know how much a soap washing removed. The combination of washing nets and determining the remaining insecticide thus provide a method for evaluating the wash resistance of a net, a parameter that may be used for estimating the field longevity of a net.
The WHO protocol  for regenerating nets operates with a constant regeneration interval between washes. This study shows that the regenerating time increased with the number of washes. Since it is very unlikely that people will wash their nets with few days interval, it can be expected that nets normally will have time enough to regenerate before next washing. Accordingly, tracing the development of the regeneration time along the wash resistance study as done here and then applying it along the exhaustion process gives a realistic picture of the wash resistance of the net.
This study introduced a new way of measuring MKDT (Figure 1). MKDT studies are easy to implement, since the results are obtained within minutes compared to the 24 hours of the mortality bioassay, but several test tools used have given different results. The WHO test tube has been used with a treated or non-treated net at the open end of the tube, giving two different results. Nets have been wrinkled in one [2–4] or two  layers around a grid ball, the two layers to avoid that the mosquitoes can escape. However, this also means operating with two different dosages, since mosquitoes now may touch nets in two layers. Yates et al  also report very little variation in median MKDT in repeated tests, whereas the inter-sample variation found in median MKDT by Graham et al  from single nets may be due to the heterogeneity of the impregnation of the tested nets. Under more controlled situations, it has been discussed whether the differences in results between laboratories are due to the mosquito's ability to avoid contact with the treated surface in some bioassays (by flying around or sitting on other surfaces than the treated net) . Also, difficulties of seeing the mosquitoes clear enough through the double layer of net may impact on results and variability in readings (John Gimnic, pers. comm.).
By using a transparent glass plate covering a 10 cm round hole in a 10 mm thick Plexiglas plate, these inconveniences are solved. Mosquitoes are easy to observe and the height of the hole allow them to walk around on the net, but not to fly. Therefore, they are in forced contact with the net sample all the time. The hole in the glass lid makes it easy to introduce and remove mosquitoes by moving the plate around above the net sample (Figure 1).
The present article presents a new way to measure regeneration time. This method is recommended especially for following changes in surface concentrations of insecticide treated materials. Linearity of the method is documented for coated nets as for a commercial insecticide incorporated net. For LNs, the method provides a complementary and reliable way in determining regeneration time after washing.
We thank Prof. C.F. Curtis, London School of Hygiene and Tropical Medicine, who recently passed away, for reviewing the manuscript.
- WHO: Guidelines for laboratory and field testing of long-lasting insecticidal mosquito nets. WHO/CDS/WHOPES/GCDPP/2005.1. 2005, World Health Organization, GenevaGoogle Scholar
- WHO: Test procedures for insecticide resistance, bio-efficacy and persistence of insecticides on treated surfaces. In Report of WHO Informal Consultation 1998: WHO/CDS/CPC/MAL/98.12. 1998, World Health Organization, GenevaGoogle Scholar
- Curtis CF, Maxwell CA, Finch RJ, Njunwa KJ: A comparison of use of a pyrethroid either for house spraying or for bednet treatments against malaria vectors. Trop Med Int Health. 1998, 3: 619-631.View ArticlePubMedGoogle Scholar
- WHO: Report of the WHO Informal Consultation on the evaluation of Insecticides. WHO/CTD/WHOPES/IC/96.1. 1996, World Health Organization, GenevaGoogle Scholar
- Maxwell CA, Myamba J, Magoma J, Rwegoshora RT, Magesa SM, Curtis CF: Test of Olyset nets by bioassay and in experimental huts. J Vector Borne Dis. 2006, 43 (1): 1-6.PubMedGoogle Scholar
- Yates A, N'Guessan R, Kaur H, Akogbéto M, Rowland M: Evaluation of KO-Tab 1–2–3®: a wash-resistant 'dip-it-yourself' insecticide formulation for long-lasting treatment of mosquito nets. Malar J. 2005, 4: 52-10.1186/1475-2875-4-52.PubMed CentralView ArticlePubMedGoogle Scholar
- Graham K, Kayedi MH, Maxwell C, Kaur H, Rehman H, Malima R, Curtis CF, Lines JD, Rowland MW: Multi-country field trials comparing wash-resistance of Permanet® and convention insecticide-treated nets against anopheline and culicine mosquitoes. Med Vet Entomol. 2005, 19: 72-83. 10.1111/j.0269-283X.2005.00543.x.View ArticlePubMedGoogle Scholar
This article is published under license to BioMed Central Ltd. This is an Open Access article distributed under the terms of the Creative Commons Attribution License (http://creativecommons.org/licenses/by/2.0), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.